Child-Restraint System Suitability for Various Seat Positions Table
(Mexico)
Provided information in the table shows your child-restraint system suitability for various seating position. For installation suitability of other manufacturer child-restraint system, carefully consult the manufacturer's instructions which accompany the child-restraint system.
When installing a child-restraint system, the following points must be observed:
-
Always remove the head restraint before installing a child-restraint system. However, when installing a backless booster seat, always install the vehicle head restraint to the seat where the backless booster seat is installed. In addition, always use a tether strap and attach it securely. Refer to Head Restraints (Search).
-
When installing a child-restraint system to the front passenger seat, adjust the seat slide position as far back as possible.
Refer to Adjusting the Front Passenger's Seat (Search).
-
When it is difficult to install a child-restraint system to the front passenger seat, or the seat belt cannot be secured to the child-restraint system, perform the following operations to adjust the seat holding the child-restraint system so that the seat belt can be secured completely to it.
-
Move the seat forward or back.
-
Move the seatback forward or back.
-
-
When installing a child-restraint system to the rear seat, adjust the front seat position so that the front seat does not contact the child-restraint system.
Refer to Adjusting the Driver's Seat (Search).
Refer to Adjusting the Front Passenger's Seat (Search).
-
When installing a child-restraint system equipped with a tether, remove the head restraint.
Refer to Head Restraints (Search).
-
An i-Size child-restraint system refers to a child-restraint system which has acquired i-Size category certification for the UN-R 129 regulation.
When installing a child-restraint system to the rear seat, refer to the child-restraint system manufacturer's instructions and the Using ISOFIX Lower Anchor (Search).
|
Seating position |
Passenger |
Rear (Left) |
Rear (Center) |
Rear (Right) |
|---|---|---|---|---|
|
Seating position suitable for universal belted (Yes/No) |
Yes (UF) |
Yes (U) |
Yes (U) |
Yes (U) |
|
i-Size seating position (Yes/No) |
No |
Yes（i-U） |
No |
Yes（i-U） |
|
Largest suitable rearward facing fixture (R1) |
No |
Yes (IL) |
No |
Yes (IL) |
|
Largest suitable rearward facing fixture (R2) |
No |
Yes (IL) |
No |
Yes (IL) |
|
Largest suitable rearward facing fixture (R2X) |
No |
Yes (IL) |
No |
Yes (IL) |
|
Largest suitable rearward facing fixture (R3) |
No |
Yes (IL) |
No |
Yes (IL) |
|
Largest suitable forward facing fixture (F2) |
No |
Yes (IUF) |
No |
Yes (IUF) |
|
Largest suitable forward facing fixture (F2X) |
No |
Yes (IUF) |
No |
Yes (IUF) |
|
Largest suitable forward facing fixture (F3) |
No |
Yes (IUF) |
No |
Yes (IUF) |
|
Largest suitable lateral facing fixture (L1) |
No |
No |
No |
No |
|
Largest suitable lateral facing fixture (L2) |
No |
No |
No |
No |
|
Largest suitable booster fixture (B2) |
No |
Yes (IUF) |
No |
Yes (IUF) |
|
Largest suitable booster fixture (B3) |
No |
Yes (IUF) |
No |
Yes (IUF) |
|
Non i-size compatible with a support leg (Yes/No) |
Yes*1 |
Yes |
No |
Yes |
|
Lower ISOFIX anchorages but without Top Tether (Yes/No) |
No |
No |
No |
No |
U = Suitable for “universal” category restraints approved for use in this mass group.
UF = Suitable for forward-facing “universal” category restraints approved for use in this mass group.
IUF = Suitable for ISOFIX forward child restraints systems of universal category approved for use in the mass group.
L = Suitable for particular child restraints given on attached list. These restraints may be of the “specific vehicle”, “restricted” or “semi-universal” categories.
IL = Suitable for particular ISOFIX child restraint systems (CRS) given in the attached list. These ISOFIX CRS are those of the “specific vehicle”, “restricted” or “semi-universal” categories.
i-U = Suitable for i-Size “universal” Child Restraint Systems forward and rearward facing.
i-UF = Suitable for forward-facing i-Size “universal” Child Restraint Systems only.
Yes = Child-restraint system can be secured on the seat.
No = Child-restraint system cannot be secured on the seat, or there is no fixture.
X = Child-restraint system cannot be installed.
-
Child restraint system can only be installed in the forward-facing position.
A Mazda genuine child-restraint system can be installed. Regarding child-restraint systems which can be installed, refer to the accessories catalog.
(Except Mexico)
-
Regarding child-restraint systems which can be installed to your Mazda, consult an Authorized Mazda Dealer.
-
A child-restraint system with a support leg cannot be installed on the rear center seat position.
-
Please comply with the legal regulations concerning the use of child-restraint systems in your country.
-
For the CRS which do not carry the ISO/XX size class identification (A to G), for the applicable mass group, the child seat manufacturer shall indicate the vehicle specific LATCH child-restraint systems recommended for each position.
